View BAOOSTSERIES_4173195.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

87 regulator ics low saturation voltage type regulator with on / off switch ba st series the ba st series are variable, fixed output low drop-out type voltage regulators with an on / off switch. these regulators are used to provide a stabilized output voltage from a fluctuating dc input voltage. fixed output voltages are 3v * , 3.3v, 5v, 6v * 7v, 8v, 9v, 10v, 12v, and 15v * . the maximum current capacity is 1a for each of the above voltages. (items marked with an asterisk are under development.) applications constant voltage power supply features 1) built-in overvoltage protection circuit, overcurrent protection circuit and thermal shutdown circuit. 2) to220fp-5 package can be used in wide range of applications. 3) 0 m a (design value) circuit current when switch is off. 4) richly diverse lineup. 5) low minimum i / o voltage differential. product codes absolute maximum ratings (ta = 25 c)
88 regulator ics ba st series block diagram
89 regulator ics ba st series pin descriptions recommended operating conditions ba00st ba03st (under development) ba033st ba05st ba06st (under development) ba07st ba08st ba09st ba10st ba12st ba15st (under development)
90 regulator ics ba st series electrical characteristics ba00st (unless otherwise noted, ta = 25 c, v cc = 10v, io = 500ma) ba03st (unless otherwise noted, ta = 25 c, v cc = 8v, io = 500ma) (under development)
91 regulator ics ba st series ba033st (unless otherwise noted, ta = 25 c, v cc = 8v, io = 500ma) ba05st (unless otherwise noted, ta = 25 c, v cc = 10v, io = 500ma)
92 regulator ics ba st series ba06st ( unless otherwise noted, ta = 25 c, v cc = 11v, io = 500ma) (under development) ba07st (unless otherwise noted, ta = 25 c, v cc = 12v, io = 500ma)
93 regulator ics ba st series ba08st (unless otherwise noted, ta = 25 c, v cc = 13v, io = 500ma) ba09st (unless otherwise noted, ta = 25 c, v cc = 14v, io = 500ma)
94 regulator ics ba st series ba10st (unless otherwise noted, ta = 25 c, v cc = 15v, io = 500ma) ba12st (unless otherwise noted, ta = 25 c, v cc = 17v, io = 500ma)
95 regulator ics ba st series ba15st (unless otherwise noted, ta = 25 c, v cc = 20v, io = 500ma) (under development)
96 regulator ics ba st series measurement circuits (the c pin only exists on the ba00ast, for the ba00ast, place a 6.8 k w resistor between the out and c pins, and a 2.2 k w resistor between the c and gnd pins.)
97 regulator ics ba st series operation notes (1) operating power supply voltage when operating within the normal voltage range and within the ambient operating temperature range, most circuit functions are guaranteed. the rated values cannot be guaranteed for the electrical characteristics, but there are no sudden changes of the characteristics within these ranges. (2) power dissipation heat attenuation characteristics are noted on a separate page and can be used as a guide in judging power dis- sipation. if these ics are used in such a way that the allowable power dissipation level is exceeded, an increase in the chip temperature could cause a reduction in the current capability or could otherwise adversely affect the perfor- mance of the ic. make sure a sufficient margin is allowed so that the allowable power dissipation value is not ex- ceeded. (3) output oscillation prevention and bypass capacitor be sure to connect a capacitor between the output pin and gnd to prevent oscillation. since fluctuations in the valve of the capacitor due to temperature changes may cause oscillations, a tantalum electrolytic capacitor with a small internal series resistance (esr) is recom- mended. a 22 m f capacitor is recommended; however, be aware that if an extremely large capacitance is used (1000 m f or greater), then oscillations may occur at low frequen- cies. therefore, be sure to perform the appropriate verifi- cations before selecting the capacitor. also, we recommend connecting a 0.33 m f bypass ca- pacitor as close as possible between the input pin and gnd. (4) current overload protection circuit a current overload protection circuit is built into the out- puts, to prevent ic destruction if the load is shorted. this protection circuit limits the current in the shape of a '7'. it is designed with a high margin, so that even if a large current suddenly flows through the large capacitor in the ic, the current is restricted and latching is prevented. however, these protection circuits are only good for pre- venting damage from sudden accidents. the design should take this into consideration, so that the protection circuit is not made to operate continuously (for instance, clamping at an output of 1v f or greater; below 1v f , the short mode circuit operates). note that the capacitor has negative temperature characteristics, and the design should take this into consideration. (5) thermal overload circuit a built-in thermal overload circuit prevents damage from overheating. when the thermal circuit is activated, the various outputs are in the off state. when the tempera- ture drops back to a constant level, the circuit is restored. (6) internal circuits could be damaged if there are modes in which the electric potential of the application's input (v cc ) and gnd are the opposite of the electric po- tential of the various outputs. use of a diode or other such bypass path is recommended. (7) although the manufacture of this product includes rigorous quality assurance procedures, the product may be damaged if absolute maximum ratings for voltage or operating temperature are exceeded. if damage has oc- curred, special modes (such as short circuit mode or open circuit mode) cannot be specified. if it is possible that such special modes may be needed, please consid- er using a fuse or some other mechanical safety mea- sure. (8) when used within a strong magnetic field, be aware that there is a slight possibility of malfunction.
external dimensions (units: mm) 98 regulator ics ba st series electrical characteristic curves

▲Up To Search▲

Price & Availability of BAOOSTSERIES

	To Download BAOOSTSERIES Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .